Home » #43 SR400

#43 SR400

2015.1.17

Custom Bike

#43 SR400Custom Report

An SR400 made to fit the physique of a large owner, as per their request.

We extended the fork with a 2%er 15cm long Joints for Front Fork (pair) [SR400/500] and converted the front wheel to 16 inches with custom spokes,

We enlarged the vehicle size with “Swingarm 5cm extension processing” and a 16″ Kit Steel Spoke SR400/500 Rear.

The frame under the seat has been straight drop processed.

With the lowered seat height, you can ride comfortably at high speeds and in the city with the “Mid High Step Kit”.

Although it’s a type 3 SR with a time-consuming immobilizer, we’ve cleaned up under the seat.

We’ve mounted the trip meter, handle lock, and helmet holder in inconspicuous places.

Custom List

FrontHandlebars, F forks, headlights, etc.

【Front Fork Area】

“2%er 15cm long Joints for Front Fork (pair) [SR400/500]“

〇A high-quality stainless steel fork joint. By becoming a long wheelbase, even a light SR body will have increased high-speed stability.

【Front Wheel】

◯A front 16-inch wheel assembled with custom spokes. We used a tire with a classic pattern.

【Headlight】

“5.75 inch Bates Light Black Body/Chrome Rim”

◯A classic headlight that matches well with the SR’s vehicle size and fork width.

“Bottom Mount Light Stay III“

◯By raising the headlight above the frame line, it creates a style with more of a chopper feel.

【Handle/Handle Area】

◯The robot handle is a one-off made of stainless steel. It is made to fit the owner’s physique. The handle clamp is carved and rounded on the XS type top bridge.

“Amal type slot wire 1200mm ’88~’08“

“300mm Long Brake Cable“

“200mm Long Clutch Cable“

◯We use each long cable for a simple throttle.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the handle area. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.

“Extension meter cable joint“

〇Used when extending the fork or relocating the meter.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“Fishtail End Tip“

◯One-off Fishtail Muffler.

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.

【Seat】

◯The seat rail drop process is done straight down. It boasts excellent strength, precision, and durability. We’ve neatly organized the difficult-to-handle electrical components under the seat of the high-year model SR, making them less noticeable.

【Gasoline Tank Installation】

◯ A one-off gas tank with rib processing in the center. Supported by a three-point rubber mount. It is installed safely.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it with a rubber mount.

【Electrical Equipment】

◯The immobilizer-equipped main key has been relocated to the lower left of the seat.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without difficulty even with LED turn signals, supporting 1-150 watts. It can also be used as a replacement for the original relay.

【Engine Area】

“Breather filter SR400/500“